Matrix Stepper Owner's Manual download pdf (Page 7)

110 V UNITS

All Matrix 3x, 5x, 7xe and 7xi 110 V Steppers require the use of

a 100-125 V, 60 Hz and a 15 A “Dedicated Circuit”, with a non-

looped (isolated) neutral/ground for power. This outlet should be

a NEMA 5-15R and have the same configuration as the plug. No

adapter should be used with this product. Steppers can be daisy-

chained together with up to 4 units per 15 A dedicated circuit.

Matrix daisy-chain cord adapters are sold separately.

220 V UNITS

All Matrix 3x, 5x, 7xe and 7xi 220 V Steppers require the use of

a 216-250 V, 50 Hz and a 15 A “Dedicated Circuit”, with a non-

looped (isolated) neutral/ground for power. This outlet should be

a NEMA 6-15R and have the same configuration as the plug. No

adapter should be used with this product. These Steppers can

be daisy-chained together with up to 4 units per dedicated 15 A

circuit. Matrix daisy-chain cord adapters are sold separately.

GROUNDING INSTRUCTIONS

The unit must be grounded. If it should malfunction or breakdown,

grounding provides a path of least resistance for electric current

to reduce the risk of electric shock. The unit is equipped with a

cord having an equipment-grounding conductor and a grounding

plug. The plug must be plugged into an appropriate outlet that

is properly installed and grounded in accordance with all local

codes and ordinances. If the user does not follow these grounding

instructions, the user could void the Matrix limited warranty.

ADDITIONAL ELECTRICAL INFO

In addition to the dedicated circuit requirement, the proper

gauge wire must be used from the circuit breaker box, to

each outlet that will have the maximum number of units

running off of it. If the distance from the circuit breaker box

to each outlet, is 100 ft (30.5 m) or less, then 12 gauge

wire should be used. For distances greater than 100 ft

(30.5 m) from the circuit breaker box to the outlet, a 10

gauge wire should be used.

ENERGY SAVING / LOW-POWER MODE

All units are configured with the ability to enter into an

energy saving / low-power mode when the unit has not

been in use for a specified period of time. Additional time

may be required to fully reactivate this unit once it has

entered the low-power mode. This energy saving feature

may be enabled or disabled from within the ‘Manager

Mode’ or ‘Engineering Mode.’

ADD-ON PCTV (3X AND 5X)

A 15 A or 20 A “Dedicated Circuit” with a non-looped

(isolated) neutral/ground is required. Each PCTV requires

at least 1.2 A of current. No more than 12 PCTVs should

be used for each 15 A circuit and no more than 16 PCTVs

should be used for each 20 A circuit. The power outlet

should have the same configuration as the plug. No

adapter should be used with this product. An RG6 coaxial

cable with ‘F Type’ compression fittings will need to be

connected between the video source and each add-on

PCTV unit.

ADD-ON DIGITAL TV (3X AND 5X)

Additional power requirements are not needed for the

add-on digital TV. An RG6 coaxial cable with ‘F Type’

compression fittings will need to be connected between

the video source and each add-on digital TV unit.

220 NEMA 6-15P

PLUG

110 NEMA 5-15P

PLUG

North American power cord

plugs shown. Depending on

your country, the plug type

may vary.

1 2 3 4 5 6 7 8 9 10 11 12 ... 51 52

Comments to this Manuals

No comments

Matrix Stepper Owner's Manual Page 7

Comments to this Manuals

Related products and manuals for Fitness, gymnastics & weight training Matrix Stepper